Pony Bead Pattern Maker
Free. No watermark. No sign-up.
Or drop a picture on the preview, or paste one.
Turning a picture into a pony bead pattern
Open a picture with a clear outline
Choose picture opens a file from your device, and a picture dropped on the preview or pasted from the clipboard works too. Remove background is ticked when the page opens, so a plain backdrop turns into empty cells and only the animal or shape is left to string.
Pick the width and the colors
Width in beads goes from 3 to 60 and starts at 16. The number beside it, 16 x 11 for the sample strawberry, is beads across by rows down. Colors goes from 2 to 24 and starts at 8.
Save the sheet
Download pattern (PNG) gives a white sheet with the bead total, the finished size, the chart with a letter in every bead and a key of letters, colors and counts. Download picture (PNG) saves the design as flat color with no lines.
What the pony bead pattern maker does
Cells the shape of a strung bead
A pony bead on a cord shows its side, 6 mm along the cord and 9 mm tall. The chart uses that 2 to 3 shape, so a round face stays round once it is beaded.
Only the shape gets beads
With Remove background on, each row is only as long as the picture's outline at that height, short at a nose or a tail and long across a body.
Straight rows, one per pass of the cord
Nothing is staggered. A chart row is one row of beads, strung in the order shown, which is how bead pets and row-by-row banners are put together.
Size worked out from the beads
Finished size shows centimeters and inches under the bead total. The 16 bead sample is about 9.6 cm wide and 9.9 cm tall.
Three ways to look at the preview
Bead look draws every bead as a ring. Symbols adds its letter. Grid lines outlines each cell. Switch them in any mix while you check the design.
Every color counted
Pony beads to use lists each color with a hex code and the number to pull from the box, so you know before you start whether you have enough.
What are pony beads?
Pony beads are chunky plastic barrel beads. The standard one is 9 mm across and 6 mm high with a 4 mm hole, and the mini size is 6.5 mm by 4 mm with a 3 mm hole. That oversized hole is the point: a cord fits through it twice.
Bead pets depend on it. You loop a cord through a key ring so two ends hang down, slide a row of beads onto one end, then push the other end through the same beads from the opposite side and pull. The row locks under the one before, and the animal grows a row at a time: lizards, turtles, dragonflies. Guides allow about two yards of cord for one lizard key chain.
The same beads make kandi, where they are woven into bracelets. For those, use the kandi pattern maker.
Pony bead pattern sizes
Each bead adds 6 mm to a row and each row adds 9 mm of height, so 11 rows come to about 10 cm. The widths below are what the tool reports for standard beads.
| Width in beads | Centimeters | Inches |
|---|---|---|
| 8 | 4.8 | 1.9 |
| 12 | 7.2 | 2.8 |
| 16 | 9.6 | 3.8 |
| 24 | 14.4 | 5.7 |
| 40 | 24.0 | 9.4 |
| 60 | 36.0 | 14.2 |
More pattern tools
Perler Bead Pattern Maker
Turn a picture into a Perler pattern with a bead count.
Hama Bead Pattern Maker
Turn a picture into a Hama pattern with a bead count.
Artkal Bead Pattern Maker
Turn a picture into an Artkal pattern with a bead count.
Kandi Pattern Maker
Turn a picture into a kandi cuff pattern for pony beads.
Bead Loom Pattern Maker
Turn a picture into a loom pattern for seed beads.
Peyote Pattern Maker
Peyote stitch patterns with offset columns.
Brick Stitch Pattern Maker
Brick stitch patterns with offset rows.
Alpha Pattern Generator
Alpha friendship bracelet patterns from pictures.
Perler Bead Letters
Type a name and get a bead letter pattern.
Pony bead pattern FAQ
What can I make from a pony bead pattern?
Anything strung in level rows. That covers bead pets, key chains, zipper pulls and hanging banners. Small animals need only the low end of the Width in beads slider, which starts at 3. A banner can use the full 60, which is about 36 cm of beads.
How do I string a bead pet from the chart?
Fold the cord in half through a key ring or lanyard hook. Take the top chart row and slide its beads onto one end, left to right. Push the other end through those beads from the far side and pull both ends until the row sits tight. Do the same for each row down, then finish with a double knot.
How much cord does a pony bead pattern need?
Every row uses its own width from each end of the cord. For a safe figure, multiply the piece's width by the number of rows, double it, and add extra for the knots and the key ring. The 16 by 11 sample is 9.6 cm wide, which works out to a little over 2 meters. Buy cord thin enough to pass through a bead twice.
Why are the cells on the chart taller than they are wide?
Because the bead is. On a cord it lies with the hole sideways, so it covers 6 mm of the row but stands 9 mm high. Chart the same animal on square graph paper and the real one comes out half again as tall as the drawing. Here the stretch is already allowed for.
Can I use mini pony beads with this pattern?
Yes. A mini bead is 4 mm along the cord and 6.5 mm tall, nearly the same proportions as the standard one, so the design keeps its shape. It just comes out smaller: about two thirds of the width in Finished size, and a little under three quarters of the height.
What do I do when a row has a gap in the middle?
A gap appears where the outline splits, between two ears or two legs. A cord cannot jump it without showing. Either fill the empty cells with beads in a background color, or string each part on its own length of cord. Pictures with one solid outline avoid the problem.
How do I add legs or a tail to a bead animal?
The chart covers the body, row by row. Legs are made on one end of the cord only: string the leg beads and the toe beads, then send the cord back through just the leg beads, so the toes hold it. One common lizard uses 2 leg beads and 3 toes. Count those beads on top of the tool's total.
Do the colors match the pony beads sold in craft packs?
They are close guides, not catalog colors. The tool chooses its colors from the picture and labels them with hex codes, while a mixed pack of pony beads holds whatever shades its maker put in. Lower Colors until the list is no longer than the colors you own, then match each swatch by eye.
When should I turn Remove background off?
For a banner or any rectangle where the background is beaded too. With the box unticked every cell gets a bead and the bead total rises to the full width times rows. Leave it on for animals and cut-out shapes. It only clears a plain color that reaches the picture's edge.
Is a pony bead pattern the same as a fuse bead pattern?
No. Fuse beads stand upright on a pegboard and get ironed, so their grid is square. Pony beads are strung, lie on their side and need the taller cells drawn here. A pattern made for one comes out squashed or stretched in the other. For ironed designs use the Perler bead pattern maker.
Can I print the pony bead chart in black and white?
Yes. The downloaded sheet puts a letter in every bead and repeats the letters in the key, so the colors are not needed to follow it. Row and column numbers mark the first and every fifth line, and a heavier line falls every 10 beads to help you keep your place.